Network Configuration Reference¶

Network configuration is critical for building a high performance Ceph Storage Cluster. The Ceph Storage Cluster does not perform request routing or dispatching on behalf of the Ceph Client. Instead, Ceph Clients make requests directly to Ceph OSD Daemons. Ceph OSD Daemons perform data replication on behalf of Ceph Clients, which means replication and other factors impose additional loads on Ceph Storage Cluster networks.

Our Quick Start configurations provide a trivial Ceph configuration file that sets monitor IP addresses and daemon host names only. Unless you specify a cluster network, Ceph assumes a single “public” network. Ceph functions just fine with a public network only, but you may see significant performance improvement with a second “cluster” network in a large cluster.

It is possible to run a Ceph Storage Cluster with two networks: a public (front-side) network and a cluster (back-side) network. However, this approach complicates network configuration (both hardware and software) and does not usually have a significant impact on overall performance. For this reason, we generally recommend that dual-NIC systems either be configured with two IPs on the same network, or bonded.

If, despite the complexity, one still wishes to use two networks, each Ceph Node will need to have more than one NIC. See Hardware Recommendations - Networks for additional details.

IP Tables¶

By default, daemons bind to ports within the 6800:7300 range. You may configure this range at your discretion. Before configuring your IP tables, check the default iptables configuration.

sudo iptables -L

Some Linux distributions include rules that reject all inbound requests except SSH from all network interfaces. For example:

REJECT all -- anywhere anywhere reject-with icmp-host-prohibited

You will need to delete these rules on both your public and cluster networks initially, and replace them with appropriate rules when you are ready to harden the ports on your Ceph Nodes.

Monitor IP Tables¶

Ceph Monitors listen on ports 3300 and 6789 by default. Additionally, Ceph Monitors always operate on the public network. When you add the rule using the example below, make sure you replace {iface} with the public network interface (e.g., eth0, eth1, etc.), {ip-address} with the IP address of the public network and {netmask} with the netmask for the public network.

sudo iptables -A INPUT -i {iface} -p tcp -s {ip-address}/{netmask} --dport 6789 -j ACCEPT

MDS and Manager IP Tables¶

A Ceph Metadata Server or Ceph Manager listens on the first available port on the public network beginning at port 6800. Note that this behavior is not deterministic, so if you are running more than one OSD or MDS on the same host, or if you restart the daemons within a short window of time, the daemons will bind to higher ports. You should open the entire 6800-7300 range by default. When you add the rule using the example below, make sure you replace {iface} with the public network interface (e.g., eth0, eth1, etc.), {ip-address} with the IP address of the public network and {netmask} with the netmask of the public network.

For example:

sudo iptables -A INPUT -i {iface} -m multiport -p tcp -s {ip-address}/{netmask} --dports 6800:7300 -j ACCEPT

OSD IP Tables¶

By default, Ceph OSD Daemons bind to the first available ports on a Ceph Node beginning at port 6800. Note that this behavior is not deterministic, so if you are running more than one OSD or MDS on the same host, or if you restart the daemons within a short window of time, the daemons will bind to higher ports. Each Ceph OSD Daemon on a Ceph Node may use up to four ports:

One for talking to clients and monitors.
One for sending data to other OSDs.
Two for heartbeating on each interface.

When a daemon fails and restarts without letting go of the port, the restarted daemon will bind to a new port. You should open the entire 6800-7300 port range to handle this possibility.

If you set up separate public and cluster networks, you must add rules for both the public network and the cluster network, because clients will connect using the public network and other Ceph OSD Daemons will connect using the cluster network. When you add the rule using the example below, make sure you replace {iface} with the network interface (e.g., eth0, eth1, etc.), {ip-address} with the IP address and {netmask} with the netmask of the public or cluster network. For example:

sudo iptables -A INPUT -i {iface}  -m multiport -p tcp -s {ip-address}/{netmask} --dports 6800:7300 -j ACCEPT

Tip

If you run Ceph Metadata Servers on the same Ceph Node as the Ceph OSD Daemons, you can consolidate the public network configuration step.

Ceph Networks¶

To configure Ceph networks, you must add a network configuration to the [global] section of the configuration file. Our 5-minute Quick Start provides a trivial Ceph configuration file that assumes one public network with client and server on the same network and subnet. Ceph functions just fine with a public network only. However, Ceph allows you to establish much more specific criteria, including multiple IP network and subnet masks for your public network. You can also establish a separate cluster network to handle OSD heartbeat, object replication and recovery traffic. Don’t confuse the IP addresses you set in your configuration with the public-facing IP addresses network clients may use to access your service. Typical internal IP networks are often 192.168.0.0 or 10.0.0.0.

Tip

If you specify more than one IP address and subnet mask for either the public or the cluster network, the subnets within the network must be capable of routing to each other. Additionally, make sure you include each IP address/subnet in your IP tables and open ports for them as necessary.

Note

Ceph uses CIDR notation for subnets (e.g., 10.0.0.0/24).

When you have configured your networks, you may restart your cluster or restart each daemon. Ceph daemons bind dynamically, so you do not have to restart the entire cluster at once if you change your network configuration.

Public Network¶

To configure a public network, add the following option to the [global] section of your Ceph configuration file.

[global]
        # ... elided configuration
        public network = {public-network/netmask}

Cluster Network¶

If you declare a cluster network, OSDs will route heartbeat, object replication and recovery traffic over the cluster network. This may improve performance compared to using a single network. To configure a cluster network, add the following option to the [global] section of your Ceph configuration file.

[global]
        # ... elided configuration
        cluster network = {cluster-network/netmask}

We prefer that the cluster network is NOT reachable from the public network or the Internet for added security.

Ceph Daemons¶

The monitor daemons are each configured to bind to a specific IP address. These addresses are normally configured by your deployment tool. Other components in the Ceph system discover the monitors via the mon host configuration option, normally specified in the [global] section of the ceph.conf file.

[global]
    mon host = 10.0.0.2, 10.0.0.3, 10.0.0.4

The mon host value can be a list of IP addresses or a name that is looked up via DNS. In the case of a DNS name with multiple A or AAAA records, all records are probed in order to discover a monitor. Once one monitor is reached, all other current monitors are discovered, so the mon host configuration option only needs to be sufficiently up to date such that a client can reach one monitor that is currently online.

The MGR, OSD, and MDS daemons will bind to any available address and do not require any special configuration. However, it is possible to specify a specific IP address for them to bind to with the public addr (and/or, in the case of OSD daemons, the cluster addr) configuration option. For example,

[osd.0]
        public addr = {host-public-ip-address}
        cluster addr = {host-cluster-ip-address}

One NIC OSD in a Two Network Cluster

Generally, we do not recommend deploying an OSD host with a single NIC in a cluster with two networks. However, you may accomplish this by forcing the OSD host to operate on the public network by adding a public addr entry to the [osd.n] section of the Ceph configuration file, where n refers to the number of the OSD with one NIC. Additionally, the public network and cluster network must be able to route traffic to each other, which we don’t recommend for security reasons.

Network Config Settings¶

Network configuration settings are not required. Ceph assumes a public network with all hosts operating on it unless you specifically configure a cluster network.

Public Network¶

The public network configuration allows you specifically define IP addresses and subnets for the public network. You may specifically assign static IP addresses or override public network settings using the public addr setting for a specific daemon.

public network

Description: The IP address and netmask of the public (front-side) network (e.g., 192.168.0.0/24). Set in [global]. You may specify comma-separated subnets.
Type: {ip-address}/{netmask} [, {ip-address}/{netmask}]
Required: No
Default: N/A

public addr

Description: The IP address for the public (front-side) network. Set for each daemon.
Type: IP Address
Required: No
Default: N/A

Cluster Network¶

The cluster network configuration allows you to declare a cluster network, and specifically define IP addresses and subnets for the cluster network. You may specifically assign static IP addresses or override cluster network settings using the cluster addr setting for specific OSD daemons.

cluster network

Description: The IP address and netmask of the cluster (back-side) network (e.g., 10.0.0.0/24). Set in [global]. You may specify comma-separated subnets.
Type: {ip-address}/{netmask} [, {ip-address}/{netmask}]
Required: No
Default: N/A

cluster addr

Description: The IP address for the cluster (back-side) network. Set for each daemon.
Type: Address
Required: No
Default: N/A

Bind¶

Bind settings set the default port ranges Ceph OSD and MDS daemons use. The default range is 6800:7300. Ensure that your IP Tables configuration allows you to use the configured port range.

You may also enable Ceph daemons to bind to IPv6 addresses instead of IPv4 addresses.

ms bind port min

Description: The minimum port number to which an OSD or MDS daemon will bind.
Type: 32-bit Integer
Default: 6800
Required: No

ms bind port max

Description: The maximum port number to which an OSD or MDS daemon will bind.
Type: 32-bit Integer
Default: 7300
Required: No.

ms bind ipv6

Description: Enables Ceph daemons to bind to IPv6 addresses. Currently the messenger either uses IPv4 or IPv6, but it cannot do both.
Type: Boolean
Default: false
Required: No

public bind addr

Description: In some dynamic deployments the Ceph MON daemon might bind to an IP address locally that is different from the public addr advertised to other peers in the network. The environment must ensure that routing rules are set correctly. If public bind addr is set the Ceph MON daemon will bind to it locally and use public addr in the monmaps to advertise its address to peers. This behavior is limited to the MON daemon.
Type: IP Address
Required: No
Default: N/A

TCP¶

Ceph disables TCP buffering by default.

ms tcp nodelay

Description: Ceph enables ms tcp nodelay so that each request is sent immediately (no buffering). Disabling Nagle’s algorithm increases network traffic, which can introduce latency. If you experience large numbers of small packets, you may try disabling ms tcp nodelay.
Type: Boolean
Required: No
Default: true

ms tcp rcvbuf

Description: The size of the socket buffer on the receiving end of a network connection. Disable by default.
Type: 32-bit Integer
Required: No
Default: 0

ms tcp read timeout

Description: If a client or daemon makes a request to another Ceph daemon and does not drop an unused connection, the ms tcp read timeout defines the connection as idle after the specified number of seconds.
Type: Unsigned 64-bit Integer
Required: No
Default: 900 15 minutes.